| Availabilty: |
Tunnel Boring Machine: |
| One (1) |
Robbins Model 171-231 Hard Rock TBM, 18’3” (5.56 meter) diameter, 1500 HP, 17” cutters, 460 Volt/60 cycle, complete with all trailing gear |
| One (1) |
Jarva Mark 12 Hard Rock TBM, 14’ diameter, 600 HP, 15” cutters, 460 Volt/60 Cycle. |
| One (1) |
2008 Thyssen-Krupp (Herrenknecht) S-234 TBM Bearing, triple row main bearing, 66.929 inches(1700mm) standard ID. NEW. Was spare on Arrowhead project. |
| One (1) |
2008 Thyssen-Krupp (Herrenknecht) Segment Erector Bearing, 105 inches (2678mm) standard ID. NEW. Was spare on Arrowhead project.
Back to Top>>
|
| Availabilty: |
Scooptram: |
| One (1) |
Wagner Model SST2.5 Scooptram, 2.5 cubic yard capacity, powered by a Detroit Model 471TI “D” Deck engine.
Back to Top>>
|
| Availabilty: |
Mine Service Vehicle: |
| One (1) |
Wagner Model UT45, Flat Bed, four-wheel drive, powered by a Deutz Model F6L912W engine |
| One (1) |
Getman Fuel & Lube Truck, four-wheel drive, 400 gal. fuel tank, 150 gal. hydraulic oil, 55 gal. engine oil, 55 gal. salvage oil, 5 retractable hose reels, powered by a Deutz Model F6L912W engine
Back to Top>>
|
| Availabilty: |
Mine Truck: |
| Four (4) |
2006 Sandvik Model DFP30-DT 20-ton truck, 4 x 4 Underground Articulated Dump Truck,
powered by 350 HP Mercedes engine. Less than 1200 hours each.
Back to Top>>
|
| DRILLS - UNDERGROUND - HYDRAULIC
|
| Availabilty: |
Drill: |
| One (1) |
Tamrock Paramatic 307 Three Boom Drill Jumbo, electric/hydraulic, rail mounted, 36" gauge, complete with one Model ZR650 Boom and two Model MR600 Booms, three KS140XH44 Feeds, three HV417 Power Packs and three HLR438 Drills |
| One (1) |
Atlas Copco PROMEC, Long Hole Drill, electric/hydraulic, rubber tired, complete with one 1038 Drill, drills 360 degrees |
| One (1) |
Atlas Copco Raildrill Model H201 Single Boom Drill Jumbo, electric/hydraulic, rail mounted, 24" gauge, complete with one BUT-6 Boom, one COP1022 hydraulic drill
Back to Top>>
|
| DRILLS - UNDERGROUND - AIR
|
| Availabilty: |
Drill: |
| One (1) |
Gardner Denver Model 5100 Two Boom Drill Jumbo, crawler mounted, complete with two 11' JTI
Rota-Booms, two DPT Drill positioners, two 2MSB 12' screw feeds, two PR55 drills |
| One (1) |
Gardner Denver Model 3700 Single Boom Drill Jumbo, crawler mounted, air powered, complete with one 9'6" JTI Rota-Boom, one DPT drill positioner, one 2MSB 10' screw feed, one PR55 drill |
| One (1) |
Ingersoll Rand Model 96RM-Rampmaster Two Boom Drill Jumbo with basket, rubber tired, complete with two Model LHBER Booms, one JTT Extendable Boom with basket, two 6AM16 Feeds, two Gardner Denver Model PR123 Drills, powered by Deutz Model F6L912W engine |
| Two (2) |
Gardner Denver Universal III, Three Boom Drill Jumbo, rubber tired, complete with three 11' JTI Rota-Booms, three DPT drill positioners, three 2MSB 12' screw feeds, three PR55 drills, powered by a Deutz Model F6L912W engine |
| One (1) |
Gardner Denver Medi-Bore Two Boom Drill Jumbo, rubber tired, complete with two 11' JTI Rota-Booms,
two DPT drill positioners, two 2MSB 12' screw feeds, two PR55 drills, powered by a Deutz Model
F6L912W engine |
| Four (4) |
Gardner Denver Mini-Bore Two Boom Drill Jumbo, rubber tired, complete with two 11' JTI Rota-Booms, two DPT Drill positioners, two 2MSB 12' screw feeds, two PR55 drills, powered by a Deutz Model F3L912W engine |
| Two (2) |
Gardner Denver Mini-Bore Two Boom Drill Jumbo, rubber tired, air powered, PERMISSIBLE, complete with two 9'6" Rota-Booms, two DPT drill positioners, two 2MSB 10' screw feeds, two PR55 drills |
| Four (4) |
Gardner Denver Mini-Bore Two Boom Drill Jumbo, rail-mounted, 24"/30"/36"/42” gauge, complete with two 9'6" Rota Booms, two DPT drill positioners, two 2MSB 10' screw feeds, two PR55 drills |
| One (1) |
Gardner Denver Two Boom Crawler Mounted Drill Jumbo, complete with two 9’6” Rota-Booms, two DPT drill positioners, two 2MSB 10’ screw feeds and two PR55 drills |
| |
NOTE: ALL JUMBOS CAN BE EQUIPPED WITH ALTERNATE DRILLS
Back to Top>>
|
 |
| DRILLS - HYDRAULIC AND ACCESSORIES
|
| Availabilty: |
Drill: |
| Three (3) |
Tamrock Model HLR438 Drill |
| One (1) |
Tamrock Model MR600 Boom |
| Three (3) |
Tamrock Model ZR650 Boom |
| Three (3) |
Tamrock Model ZR990 Boom |
| Four (4) |
Atlas Copco Model 1038 Drill |
| Four (4) |
Atlas Copco Model BUT 15 ERH Boom |
| Two (2) |
Atlas Copco Model BUT 10 FHH Boom |
| Six (6) |
Atlas Copco Power Pack, 60 HP, 575 Volt |
| Two (2) |
Atlas Copco Model BMH628 Feed, 23'
Back to Top>>
|
| Availabilty: |
Drill: |
| Twenty (20) |
Ingersoll Rand Model JR300 Jackleg, 7/8" chuck with leg
Back to Top>>
|
| Availabilty: |
Drill: |
| One (1) |
Atlas Copco Model ROC 400A-00 Air Track, with a BBE57 drill
Back to Top>>
|
| AIR COMPRESSORS - ELECTRIC STATIONARY
|
| Availabilty: |
Air Compressor: |
| One (1) |
Ingersoll Rand Model XLE 2100 CFM at 125 PSI, powered by a 400 HP, 4160 Volt motor, size 24-1/2” x
13-1/2” x 10”
|
| One (1) |
Ingersoll Rand Model XLE 1600 CFM at 135 PSI, size 20-1/2" x 11-1/2" x 8-1/2", powered by a 300 HP,
480 Volt motor, skid mounted
|
| Two (2) |
Ingersoll Rand, 750 CFM at 125 PSI, 150 HP, 480 Volt, complete with air dryers and receiver tanks, heavy- duty skid mounted |
| One (1) |
Ingersoll Rand Model 750, 350 CFM at 100 PSI, Size 7-1/2" x 7-1/2" x 6-1/4" x 5", skid mounted, self contained, powered by a 100 HP, 480 Volt electric motor
Back to Top>>
|
| AIR COMPRESSORS - DIESEL PORTABLE
|
| Availabilty: |
Air Compressor: |
| One (1) |
Sullair Model D1300QH, 1300 CFM, powered by a Caterpillar 3406 engine |
| Two (2) |
Gardner Denver Model Flex Air 1200, 1200 CFM, powered by Caterpillar 3406 engine
Back to Top>>
|
 |
| Availabilty: |
Pump: |
| Two (2) |
Ingersoll Rand Model 6HMTA-4, 1500 GPM at 1840' head, powered by 900 HP, 2300/4160 Volt electric motors - NEW |
| Ten (10) |
Ash Pumps Model D5, 8" x 8" x 22-1/4", 900 PSI, powered by 500 HP, 2300 Volt electric motor |
| Three (3) |
Ash Pumps Model C5-D, 6" x 6" x 19-3/8", 600 PSI, powered by 250 HP, 2300/4160 Volt motor |
| Fifteen (15) |
Ash Pumps Model C5, 6" x 6" x 19-3/8", 600 PSI, powered by 250 HP, 2300/4160 Volt electric motor |
| Seven (7) |
Ash Pumps Model CD-6-5, 400 PSI, rubber lined, 250 HP, 2300 Volt electric motor |
| Three (3) |
Hazleton Type VS, 12", Vertical Sump Pumps, 2000 GPM at 225' head, powered by 250 HP, 480 Volt electric motors |
| Ten (10) |
Ingersoll Rand Model 2MRV50, 280 GPM at 440' head, powered by 50 HP, 440 Volt electric motor |
| One (1) |
Door-Oliver Duplex Diaphragm Pumps, Type "W", 8", 7-1/2" HP, 440 Volt
Back to Top>>
|
| PUMPS - ELECTRIC SUBMERSIBLE
|
| Availabilty: |
Hoist Motor: |
| Two (2) |
Hazleton Type SS, 180 HP, 480 Volt, 3000 GPM @ 105' head, NEW
Back to Top>>
|
| Availabilty: |
Pump: |
| One (1) |
Warmon Series AA@, Size 065, Type EAR08, 20 HP, 1800 RPM, TEFC |
| One (1) |
Allis Chalmers, 2" x 2.5" SRL, 5 HP, 480 Volt
Back to Top>>
|
| Availabilty: |
Mine Fan: |
| One (1) |
TLT Babcock Model GAF 26.5/12.5-1 Axial Fan, 104" diameter, 700 HP, 880 RPM, 4160 Volt |
| Two (2) |
Joy Axivane Fan, Model M96-50VE, 96” x 1170 RPM, 300 HP, 2300 Volt, Belt Driven |
| One (1) |
Shaft Heater, 2008 Aerovent 5 Million BTU Portable, S/N 0838364611, NEW |
| |
*Mining Equipment has a very large inventory of used fans in all sizes and horsepower. Please call with your requirements and if we don’t have it in our used inventory, we can manufacture NEW Jetair fans to meet your needs.
Back to Top>>
|
| LOCOMOTIVES - BATTERY - TROLLEY
|
| Availabilty: |
Locomotives: |
| Two (2) |
General Electric 30 Ton Model 5GHM850-B4, 42" gauge, trolley, NEW |
| Six (6) |
ASEA 26 Ton Model LGBT-22, 36"/42" gauge, combination battery/trolley |
| Two (2) |
Balco 25 Ton Battery Locomotive, 36” gauge, two motor drive |
| Sixteen (16) |
General Electric 20 Ton Model LME-2C20-C2, 36" gauge, trolley |
| One (1) |
Goodman 18 Ton, Model 136B, 36" gauge, combination battery/trolley |
| Three (3) |
Goodman 15 Ton Model 136B, 36" gauge, trolley |
| Eight (8) |
General Electric 15 Ton Model LME2C15-A15, 36" gauge, trolley |
| Four (4) |
Goodman 15 Ton Model 154, 36" gauge, battery |
| Four (4) |
General Electric 13 Ton Model 2C13-A2, 36" gauge, trolley |
| One (1) |
Greensburg 12 Ton Monitor, 36" gauge, battery |
| Six (6) |
Greensburg 11 Ton, 36” gauge, battery |
| Four (4) |
Balco 10.5 Ton, 36” gauge, battery |
| Two (2) |
Goodman 10 Ton Model 136B, 36" gauge, trolley |
| One (1) |
Greensburg 10 Ton Type "C", 42" gauge, battery |
| One (1) |
Atlas 10 Ton Type D, 30" gauge, battery |
| Five (5) |
General Electric 8 Ton Model LME2C8-6W, 36" gauge, trolley |
| Twentyfive (25) |
Greensburg 8 Ton Monitor, 36" gauge, battery |
| One (1) |
Goodman 8 Ton Model 132A, 36" gauge, trolley |
| One (1) |
Plymouth 6 Ton Model EB-6, 18"/24" gauge, battery |
| One (1) |
Greensburg 6 Ton, Cruiser Monitor, 36" gauge, battery |
| One (1) |
Greensburg 6 Ton, Model H1 Type "C", 36" gauge, battery |
| Two (2) |
Greensburg 4 Ton, Monitor, 24" gauge, battery |
| Two (2) |
Mancha 3-1/2 Ton, Titan BN, 24"/30" gauge, battery |
| Three (3) |
Atlas 3 Ton, Type "K", 24" gauge, battery |
| Two (2) |
Greensburg 2-1/2 Ton, Monitor, 24" gauge, battery |
| One (1) |
Mancha 1-1/2 Ton, Model "B", "Little Trammer", 18"/20"/24" gauge, battery
Back to Top>>
|
 |
| Availabilty: |
Battery Motors: |
| Four (4) |
Goodman Model 154, 50 HP, 128 Volt |
| Sixteen (16) |
Goodman Model 142EB, 28 HP, 96 Volt |
| Ten (10) |
Goodman/Mancha Model M49B, 14 HP, 80 Volt |
| Ten (10) |
Goodman/Mancha Model M-9, 5.5 HP, 48 Volt |
| Availabilty: |
Trolly Motors: |
| One (1) |
Goodman Model 201, with blower, 125 HP, 500 Volt |
| Two (2) |
Goodman Model 201, with blower, 125 HP, 250 Volt |
| Eight (8) |
Goodman Model 81C, 120 HP, 250 Volt |
| Eight (8) |
Goodman Model 136B, 75 HP, 250 Volt |
| Two (2) |
Goodman Model 132A, 40 HP, 250 Volt |
| Ten (10) |
Goodman Model 75B, 30 HP, 250 Volt |
| Two (2) |
Goodman Model 158, 40 HP, 250 Volt
Back to Top>>
|
| GENERAL ELECTRIC TRACTION MOTORS
|
| Availabilty: |
Trolly: |
| Ten (10) |
General Electric Model 81A/C, 125 HP, 250 Volt |
| Twentyfour (24) |
General Electric Model HM840 T2, 75 HP, 250 Volt |
| Six (6) |
General Electric Model HM829, 75 HP, 250 Volt |
| Sixteen (16) |
General Electric Model 5GHM-848 A1, 65 HP, 250 Volt |
| Six (6) |
General Electric Model HM809, 60 HP, 250 Volt |
| Six (6) |
General Electric Model GHM-845, 50 HP, 250 Volt |
| Eight (8) |
General Electric Model 5GHM 839-AB4, 45 HP, 250 Volt
Back to Top>>
|
| GREENSBURG TRACTION MOTORS
|
| Availabilty: |
Battery: |
| Eightyfour (84) |
Greensburg Frame D6000, Type M160/190, 18 HP, 80 Volt |
| Availabilty: |
Trolley: |
| Two (2) |
Greensburg Frame OX3609TT, 250 Volt
Back to Top>>
|
| Availabilty: |
Trolley: |
| Fourteen (14) |
ASEA Type LJB 23-3, four pole, 75 HP, 600 Volt
Back to Top>>
|
 |
| Availabilty: |
Locomotive: |
| Four (4) |
Schöma Model D-60-32 Powered Man-rider, hydrostatic drive, 18-man capacity, powered by a Deutz Model F4L912W diesel engine |
| One (1) |
Schöma Model D-60 Powered Man-rider with additional passenger car and operator cab, hydrostatic drive, 30-man capacity, powered by a Deutz Model TCD 2011 engine. NEW. |
| One (1) |
Brookville Model BCE35UP, 35 Ton, 42" gauge, powered by a Deutz Model F10L413FW Diesel engine,
planetary drive
|
| Six (6) |
Plymouth Model MMD-24, 35 Ton, 36"/42" gauge, powered by Deutz Model F12L413FW Diesel engine |
| Sixteen (16) |
Plymouth Model JMD, 25 Ton, 36"/42" gauge, powered by a Deutz F10L413FW Diesel engine |
| One (1) |
Schöma Model CFL-DCL-180, 25 Tonne, 36” gauge, powered by a Deutz Model F8L413FRW Diesel engine |
| Two (2) |
Schöma Model CFL-DCL-150, 23 Ton, 36” gauge, powered by a Deutz F6L413FRW Diesel engine |
| Twelve (12) |
Plymouth Model DMD, 15 Ton, 36" gauge, powered by Caterpillar Model 3306 Diesel engine |
| One (1) |
Eimco 15 Ton, 40"/42"48" gauge, powered by Deutz Model F8L413FW Diesel engine |
| One (1) |
Balco 12 Ton, 36" gauge, powered by Deutz Model F8L413FW Diesel engine |
| One (1) |
Clayton 12 Ton, 24"/30"/36" gauge, hydrostatic drive, powered by a Deutz F6L912W Diesel engine |
| Two (2) |
Plymouth Model DMD-24, 12 Ton, 24"/30"/36" gauge, powered by a Deutz Model F8L714 Diesel engine |
| Four (4) |
Clayton 10 Ton, 24"/30"/36" gauge, hydrostatic drive, powered by Deutz F6L912W Diesel engine |
| Two (2) |
Plymouth Model DMD, 10 Ton, 24"/30"/36" gauge, powered by Cat D330T Turbo charged Diesel engine |
| Two (2) |
Greensburg, Model C-10, 10 Ton, 36" gauge, powered by Cat D330T Turbocharged Diesel engine |
| Four (4) |
Clayton 8 Ton, 24"/30"/36" gauge, hydrostatic drive, powered by Deutz Model F6L912W Diesel engine |
| Eight (8) |
Clayton 6 Ton, 24"/30"/36" gauge, hydrostatic drive, powered by Deutz F4L912W Diesel engine |
| Ten (10) |
Plymouth Model HMD, 8 Ton, 24"/30"/36" gauge, powered by Deutz Model F6L912W Diesel engine |
| Eight (8) |
Plymouth Model HMD, 6 Ton, 24"/30"/36" gauge, powered by Deutz Model F4L912W Diesel engine |
| Two (2) |
MEI Series II, 4 Ton, 18"/24" gauge, powered by Deutz Model FL1011 Diesel engine |
| |
NOTE: LOCOMOTIVES CAN BE FITTED WITH NEW ENGINES IF REQUIRED AND WEIGHT CAN BE ADDED.
Back to Top>>
|
 |
| Availabilty: |
Mine Car: |
| Nineteen (19) |
Moran Engineering Side Dump, 648 cubic foot capacity, 42" gauge |
| Twelve (12) |
Moran Engineering (Lift Off), 487 cubic foot capacity, 42” gauge |
| Twenty (20) |
Mining Equipment Roll-over, 487 cubic foot capacity, tandem bogie, 36” gauge, with roll-over dump |
| Nine (9) |
Moran Engineering Side Dump, 324 cubic foot capacity, 42" gauge |
| Ten (10) |
Moran Engineering (Lift Off), 270 cubic foot capacity, 24"/36" gauge |
| Twelve (12) |
Door-Oliver Side Dump, 250 cubic foot capacity, 42" gauge |
| Twentyfive (25) |
C. S. Card (Lift Off), 216 cubic foot capacity, 36" gauge |
| Ten (10) |
Moran Engineering (Lift Off), 216 cubic foot capacity, 24" gauge |
| Fortyfive (45) |
C. S. Card Granby, 200 cubic foot capacity, 36" gauge |
| Four (4) |
Sanford-Day Granby, 200 cubic foot capacity, 36" gauge |
| Three (3) |
C. S. Card Granby, 200 cubic foot capacity, 36" gauge |
| Twelve (12) |
C. S. Card Granby, 180 cubic foot capacity, 30" gauge |
| Ten (10) |
Moran Engineering Side Dump, 162 cubic foot capacity, 36" gauge |
| Twelve (12) |
Huwood Irwin Side Dump, 150 cubic foot capacity, 42" gauge
|
| Thirteen (13) |
C. S. Card Granby, 145 cubic foot capacity, 36" gauge |
| Five (5) |
C. S. Card Granby, 135 cubic foot capacity, 24" gauge |
| Seven (7) |
C. S. Card Granby, 135 cubic foot capacity, 36" gauge |
| Sixteen (16) |
Cottonwood Granby, 135 cubic foot capacity, 36" gauge |
| Thirteen (13) |
Moran Engineering (Lift Off), 135 cubic foot capacity, 24" gauge |
| Twentyfour (24) |
C. S. Card (Lift Off), 135 cubic foot capacity, 24" gauge |
| Fifteen (15) |
Sanford-Day Granby, 126 cubic foot capacity, 24" gauge |
| Thirtyfive (35) |
C. S. Card (Lift Off), 125 cubic foot capacity, 24" gauge |
| Eighteen (18) |
C. S. Card (Lift Off), 120 cubic foot capacity, 24" gauge |
| Fourteen (14) |
C. S. Card Granby, 120 cubic foot capacity, 24" gauge |
| Twentynine (29) |
C. S. Card Granby, 115 cubic foot capacity, 36" gauge |
| Twenty (20) |
C. S. Card (Lift Off), 110 cubic foot capacity, 24” gauge |
| Sixteeen (16) |
Lakeshore Granby, 100 cubic foot capacity, 24" gauge |
| Three (3) |
Sanford-Day Granby, 96 cubic foot capacity, 30"/24" gauge, air dump |
| Fourteen (14) |
C. S. Card Granby, 93 cubic foot capacity, 24" gauge |
| Three (3) |
C. S. Card Granby, 91 cubic foot capacity, 24" gauge |
| Twentyfive (25) |
C. S. Card (Lift Off), 85 cubic foot capacity, 24" gauge |
| Eight (8) |
C. S. Card (Lift Off), 80 cubic foot capacity, 18"/24" gauge |
| Nine (9) |
Sanford-Day Granby, 80 cubic foot capacity, 24" gauge |
| Twenty (20) |
JCI/Welcom Bottom Dump, 80 cubic foot capacity, 24" gauge, NEW |
| Six (6) |
C. S. Card Granby, 80 cubic foot capacity, 24" gauge |
| Six (6) |
C. S. Card (Lift Off), 80 cubic foot capacity, 24" gauge |
| Twentytwo (22) |
C. S. Card (Lift Off), 77 cubic foot capacity, 24" gauge |
| Eleven (11) |
C. S. Card Granby, 73 cubic foot capacity, 24" gauge |
| Eightteen (18) |
C. S. Card Granby, 70 cubic foot capacity, 24" gauge |
| Fiftyfour (54) |
C. S. Card Granby, 60 cubic foot capacity, 18"/24" gauge |
| Twentyeight (28) |
C. S. Card Rocker Dump, 40 cubic foot capacity, 24" gauge |
| Six (6) |
C. S. Card Rocker Dump, 32 cubic foot capacity, 24" gauge |
| Nighteight (98) |
Moran Engineering/C. S. Card Flat Car, 24"/30"/36"/42" gauge |
| Six (6) |
Mining Equipment Car, 24 man capacity, tandem bogie with brakes, 36” gauge. NEW |
| One (1) |
C. S. Card Man Car, 24 man capacity, 24"/36" gauge |
| Two (2) |
Sanford-Day Man Car, 24 man capacity, 42" gauge |
| Two (2) |
C. S. Card Man Car, 12 man capacity, 24"/30"/36" gauge |
| Two (2) |
C. S. Card Man Car, 8 man capacity, 36" gauge |
| Two (2) |
Moran Engineering Vent Line Car, 24"/30"/36" gauge, air over hydraulic, 40' capacity |
| One (1) |
Moran Engineering Explosive Car, 36" gauge |
| One (1) |
Sanford-Day Lowboy, 50-ton capacity, 42" gauge |
| Two (2) |
Sanford-Day Lowboy, 25-ton capacity, 42" gauge |
| Eight (8) |
Moran Engineering Segment Cars, 36” gauge |
| Eight (8) |
Moran Engineering Segment Cars, 42” gauge
Back to Top>>
|
 |
| CALIFORNIA SWITCH (RENT ONLY)
|
| Availabilty: |
California Switch: |
| Two (2) |
24" gauge California Switch
Back to Top>>
|
| Availabilty: |
Car: |
| Forty (40) |
Moran Engineering Agitator Car, 12 cubic yard capacity, 36"/42" gauge |
| Ninety (90) |
Moran Engineering Agitator Car, 6 cubic yard capacity, 24"/30"/36"/42" gauge |
| Thirtyfive (35) |
Moran Engineering Agitator Car, 4 cubic yard capacity, 24" gauge |
| Ten (10) |
Maxon Agimax Concrete Car, 13 cubic yard capacity, electric powered, 36” gauge
Back to Top>>
|
| Availabilty: |
Concrete Form: |
| One (1) |
Everest Ewing, 19 ft. round diameter concrete form, complete with carrier and needle beam, 75 ft. of active form. Used on one job in Dallas, TX.
Back to Top>>
|
| Availabilty: |
Form Vibrators: |
| Two Hundred (200) |
Viber Model TV-5, concrete vibrator |
| Four Hundred (400) |
Viber Model TV-7, concrete vibrator
Back to Top>>
|
| MUCKERS - RAIL, CRAWLER, OVERSHOT, RUBBER TIRED
|
| Availabilty: |
Mucker: |
| Four (4) |
Conway Model 100-2, 36"/42" gauge |
| Four (4) |
Conway Model 75, 30"/36" gauge |
| Two (2) |
Mitsui Model RS150, 30”/36" gauge |
| Four (4) |
Eimco Model 40H, 36" gauge |
| Six (6) |
Atlas Copco Model LM250, 30"/36" gauge |
| One (1) |
Atlas Copco Model LM70, 36”/42” gauge |
| Three (3) |
Eimco Model 26, 42" gauge |
| Three (3) |
Eimco Model 25, 42" gauge |
| Four (4) |
Eimco Model 24, 30" gauge |
| Ten (10) |
Eimco Model 22, 24"/30"/36" gauge |
| One (1) |
Atlas Copco Model LM56, 36” gauge |
| Twelve (12) |
Eimco Model 630, crawler mounted |
| One (1) |
Atlas Copco Cavo Model 520, rubber tired
Back to Top>>
|
| Availabilty: |
Hagglund Equipment: |
| Two (2) |
Hagglund Model 8HR-5EL Loader, 42" gauge, electric power |
| One (1) |
Hagglund Model 8HR Loader, 36" gauge, air powered |
| One (1) |
Hagglund Model 9HR Loader, crawler mounted, air powered |
| One (1) |
Hagglund Model HRST140 Shuttle Car, 14 cubic meter capacity, 36" gauge, electric power |
| Two (2) |
Hagglund Model HRST115E Shuttle Car, 11.5 cubic meter capacity, 36" gauge, electric power
Back to Top>>
|
| SLUSHERS - THREE DRUM ELECTRIC
|
| Availabilty: |
Slusher: |
| One (1) |
Ingersoll Rand Model 75NNN41D, 75 HP, 9900 lbs. pull at 250 FPM |
| Two (2) |
Joy Model C2F311, 60 HP, 7925 lbs. pull at 250 FPM |
| Two (2) |
Ingersoll Rand Model 50MMM41D, 50 HP, 6600 lbs. pull at 250 FPM |
| Four (4) |
Domeq Model 30MNM31D, 30 HP, 3960 lbs. pull at 250 FPM |
| Two (2) |
Ingersoll Rand Model 30MMM3D, 30 HP, 3960 lbs. pull at 250 FPM |
| Six (6) |
Joy Model B2F311, 30 HP, 3960 lbs. pull at 250 FPM
Back to Top>>
|
| SLUSHERS - TWO DRUM ELECTRIC
|
| Availabilty: |
Slusher: |
| Two (2) |
Joy Model RF211, 100 HP, 13200 lbs. pull at 250 FPM |
| Ten (10) |
Joy Model C2F211, 75 HP, 9900 lbs. pull at 250 FPM |
| Three (3) |
Ingersoll Rand Model 75MM41D, 75 HP, 9900 lbs. pull at 250 FPM |
| Five (5) |
Ingersoll Rand Model 50ML41D, 50 HP, 6600 lbs. pull at 250 FPM |
| Eight (8) |
Joy Model B2F211, 40 HP, 4400 lbs. pull at 250 FPM |
| Six (6) |
Joy Model B2F211, 30 HP, 3960 lbs. pull at 250 FPM |
| Six (6) |
Joy Model A2F211, 25 HP, 3300 lbs. pull at 250 FPM |
| Two (2) |
Ingersoll Rand Model 15HM2D, 1980 lbs. pull at 250 FPM |
| One (1) |
Ingersoll Rand Model 20NM2D, 2640 lbs. pull at 250 FPM |
| One (1) |
Ingersoll Rand Model 20ML2D, 2640 lbs. pull at 250 FPM |
| Two (2) |
Ingersoll Rand Model 25NM3C, 2750 lbs. pull at 300 FPM |
| Two (2) |
Ingersoll Rand Model 20NM2C, 2200 lbs. pull at 300 FPM |
| One (1) |
Ingersoll Rand Model 15ML2C, 1650 lbs. pull at 300 FPM |
| Four (4) |
Ingersoll Rand Model 15NM2C, 1650 lbs. pull at 300 FPM |
| One (1) |
Joy Model FF211, 10 HP, 2200 lbs. pull at 165 FPM
Back to Top>>
|
 |
| Availabilty: |
Slusher: |
| One (1) |
Ingersoll Rand Model K5MM2D, 1975 lbs. pull at 250 FPM |
| Two (2) |
Joy Model S211, 1100 lbs. pull at 150 FPM |
| One (1) |
Gardner Denver Model HBD, 1100 lbs. pull at 150 FPM |
| Two (2) |
Ingersoll Rand Model A5NNOH, 1100 lbs. pull at 150 FPM
Back to Top>>
|
| SLUSHER BUCKETS AND ACCESSORIES
|
| Availabilty: |
Slusher Buckets and Accessories: |
| Three (3) |
C. S. Card Model HD60, 60" Slusher Bucket |
| Three (3) |
C. S. Card Model HD50, 48" Slusher Bucket |
| Twentyfive (25) |
C. S. Card Model L48, 48" Slusher Bucket
Back to Top>>
|
| AIR TUGGERS - SINGLE DRUM
|
| Availabilty: |
Air Tuggers: |
| One (1) |
Joy Model JCP-120, 23,000 lbs. pull at 30 FPM |
| Two (2) |
Ingersoll Rand Model 25UWB, 14,000 lbs. pull at 40 FPM |
| One (1) |
Ingersoll Rand Model 35UWB, 12,500 lbs. pull at 96 FPM |
| One (1) |
Joy Model JAJ-100, 10,200 lbs. pull at 50 FPM |
| One (1) |
Ingersoll Rand Model K6U, 10,000 lbs. pull at 60 FPM |
| One (1) |
Joy Model JHAL-20, 2,000 lbs. pull at 110 FPM |
| Six (6) |
Ingersoll Rand Model HU, 2,000 lbs. pull at 124 FPM |
| Three (3) |
Ingersoll Rand Model EU, 2,000 lbs. pull at 54 FPM |
| Two (2) |
Ingersoll Rand Model D6UL, 1,000 lbs. pull at 75 FPM |
| Two (2) |
Gardner Denver Model HKL, 2,000 lbs. pull at 130 FPM
Back to Top>>
|
| ELECTRIC TUGGERS - SINGLE DRUM
|
| Availabilty: |
Electric Tugger: |
| Two (2) |
Seibu, 15 KW, 460-380V, 60-50 Hz, 2500 kg pull at 31 MPM
Back to Top>>
|
| Availabilty: |
Equipment: |
| One (1) |
Intermountain Electronics 2500 KVA, Model 7200-PC2500, Power Center, 7200 Primary, 950/480 Secondary,
skid mounted
|
| Twelve (12) |
General Electric, 300 KVA, Power Center, 4160 Primary, 480 Volt Secondary, skid mounted |
| Seven (7) |
PEMCO, 75 KVA, Model K75, Power Center, 13,800 Primary, 480 Volt Secondary, skid mounted
Back to Top>>
|
| Availabilty: |
Product: |
| One (1) |
Darda Model 7 Hydraulic Rock Splitter
Back to Top>>
|
| Availabilty: |
Pump: |
| One (1) |
Schwing Model 800 Concrete Pump, skid mounted, powered by a 150 HP, 480 Volt electric motor,
80 cubic yards per hour
|
| Two (2) |
Transcrete (Sidewinder) Concrete Pump, Model 45-VS, skid mounted, powered by a 50 HP, 480 Volt electric
motor, 45 cubic yards per hour
|
| One (1) |
Transcrete (Sidewinder) Concrete Pump, Model 45-VS, skid mounted, powered by Deutz Model F4L912W Diesel engine, 45 cubic yards per hour
Back to Top>>
|
| Availabilty: |
Equipment: |
| One (1) |
Mine & Smelter Cone Crusher, size 10" |
| |
PLEASE REMEMBER: ALL EQUIPMENT LISTED IN THIS CATALOG IS
OWNED BY MINING EQUIPMENT LIMITED AND IS PRESENTLY
AVAILABLE FOR YOUR INSPECTION.
Back to Top>>
|
 |
| Availabilty: |
Wheels: |
| One (1) |
144” diameter, spoke type. |
| Four (4) |
144” diameter, manufactured by C.S. Card. |
| Two (2) |
120” diameter for 1-1/8” rope. |
| Four (4) |
120” diameter, spoke type. |
| Two (2) |
120” diameter. |
| One (1) |
96” diameter for 1” rope, spoke type. |
| Two (2) |
96” diameter for 1-1/4” rope, liners, spoke type, able to split in half. |
| Two (2) |
62” diameter, manufactured by Wabi Iron Works, spoke type. |
| One (1) |
60” diameter for 1-3/8” rope, fabricated. |
| One (1) |
60” diameter, spoke type. |
| Three (3) |
58” diameter for 1-1/2” rope, fabricated. |
| Two (2) |
54” diameter, cast. |
| Two (2) |
48” diameter, manufactured by Dorr-Oliver-Long, spoke type. |
| Eleven (11) |
48” diameter for 1-3/8” rope, manufactured by Timberland, fabricated. |
| One (1) |
46” diameter for 1-1/8” rope, manufactured by Dorr-Oliver-Long, spoke type. |
| Four (4) |
42” diameter for 1-1/2” rope, manufactured by Timberland, fabricated. |
| One (1) |
36” diameter, fabricated. |
| One (1) |
28” diameter, fabricated. |
| One (1) |
24” diameter, cast.
Back to Top>>
|
|